The television channel Emmanuel TV is broadcast via the Intelsat 20 satellite (positioned at 68.5°E) and reaches many viewers across Africa and parts of Europe. For individuals looking to tune in, understanding the correct satellite settings including frequency, symbol rate, polarization, and the appropriate satellite position is essential. These technical details ensure that viewers receive a stable signal and clear reception when watching Emmanuel TV from their satellite dish setup.
Satellite Details Intelsat 20 and Emmanuel TV
Intelsat 20 is a geostationary communications satellite located at the 68.5°E orbital slot. Emmanuel TV uses one of the transponders on this satellite to broadcast its programming to its target regions. According to reliable sources, the key satellite parameters for Emmanuel TV on Intelsat 20 are
Key Transponder Settings
- Satellite Intelsat 20 @ 68.5°E contentReference[oaicite2]
- Frequency 12522 MHz (Kuband) contentReference[oaicite3]
- Polarization Vertical (V) contentReference[oaicite4]
- Symbol rate 27500 kS/s contentReference[oaicite5]
- FEC (Forward Error Correction) 3/4 contentReference[oaicite6]
- Video format MPEG4 HD/1080p (clear/unencrypted) contentReference[oaicite7]
These parameters let satellite receivers lock onto the correct channel when properly entered. It’s important to note that satellite settings can change over time, so users should verify periodically if Emmanuel TV updates its transponder settings.
Setting Up Your Satellite Receiver
For viewers who want to watch Emmanuel TV via Intelsat 20, the setup process typically involves the following steps. This ensures that the dish is aligned properly and the receiver is configured with correct settings.
StepByStep Setup Guide
- Ensure your satellite dish is pointed at the orbital position 68.5°E for Intelsat 20. Verify clear line of sight and aim the dish accordingly.
- Connect your LNB (Low Noise Block converter) to the receiver. Set the LNB type to Universal (975010600 MHz) if required. contentReference[oaicite8]
- In your satellite receiver’s menu, select Satellite List and choose Intelsat 20 or manually add it if not present. contentReference[oaicite9]
- Go to Transponder List or Manual Add, and enter the following Frequency = 12522 MHz, Symbol Rate = 27500 kS/s, Polarization = Vertical, FEC = 3/4. contentReference[oaicite10]
- Save the transponder settings, then perform a scan/search to pick up channels broadcasting on that transponder.
- After scanning, exit to the channel list and locate Emmanuel TV. It should appear among the channels found. Select it and start viewing.
If the signal is weak or no channels appear, ensure the dish is aligned accurately, check LNB skew/polarization settings, and confirm that the satellite feed is active and unencrypted.
Why Emmanuel TV Uses Intelsat 20 for Broadcast
Choosing a satellite like Intelsat 20 makes sense for Emmanuel TV’s broadcast strategy. The satellite covers Europe and Africa with a Kuband beam suited for directtohome (DTH) reception. By using an unencrypted feed and broadcasting in HD format, the channel maintains wide accessibility. Some of the key reasons are
- Wide footprint covering Africa and parts of Europe, enabling Emmanuel TV to reach a large viewership.
- Kuband frequencies support smaller dishes for home use, making reception feasible for many viewers.
- Using a single clear/FTA (freetoair) transponder allows supporters to access content without subscription fees.
- Consistent parameters that facilitate ease of setup by satellite installers and endusers.
Troubleshooting Common Reception Issues
Even with correct settings, viewers may encounter issues when trying to watch Emmanuel TV on Intelsat 20. Here are some typical problems and their solutions
Signal Loss or Weak Signal
If your signal strength or quality is low, consider the following
- Check dish alignment slight mispointing can drop the signal significantly.
- Ensure the LNB is functioning properly and that cables/connectors are in good condition.
- Confirm the Universal LNB is set to the correct type (975010600 MHz) if required. contentReference[oaicite11]
- Scan the receiver again and make sure you have the correct transponder frequency and symbol rate.
No Emmanuel TV Channel Found
If scanning yields channels but not Emmanuel TV, consider
- Verify that the channel list includes the correct transponder; some receivers filter channels by network or region.
- Check for recent frequency changes channels may move to a different transponder, so always refer to updated listings. contentReference[oaicite12]
- Reset or reinitialize the receiver to refresh default satellite settings.
Staying Updated with Transponder Changes
Satellite broadcasters like Emmanuel TV occasionally change transponder parameters, move to different satellites, or update their broadcast format. To remain connected, viewers should
- Refer to official Emmanuel TV announcements or their website for updates on frequency changes. contentReference[oaicite13]
- Consult satellitefrequency listing sites such as LyngSat or KingOfSat, which track changes for channels including Emmanuel TV. contentReference[oaicite14]
- Perform a new scan when you detect signal loss or channel disappearance rather than assuming equipment fault immediately.
By doing so, you ensure that any shift in broadcasting parameters is quickly addressed and your viewing continues uninterrupted.
Tuning into Emmanuel TV via Intelsat 20 is straightforward when you know the correct settings and follow proper installation steps. The key frequency is 12522 MHz, with vertical polarization and a symbol rate of 27500 kS/s on satellite position 68.5°E. With these details and accurate dish alignment, viewers across Africa and parts of Europe can access Emmanuel TV’s broadcast in HD. Regular checks for updates and awareness of signalquality factors help maintain uninterrupted viewing. Whether you are setting up a new satellite system or verifying an existing one, these guidelines will help ensure a successful reception of Emmanuel TV.